Not registered?
If you have not yet registered on the Valsir web site fill in the form with your details and obtain free access to the download area where you will be free to download our price lists and technical brochures. You will also have the possibility of receiving our periodic newsletter: the best way to remain up-to-date on all the latest developments in Valsir.
Over the last few years the market for in-wall cisterns has undergone continuous alterations dictating greater attention to technological research, to installation simplicity, to water savings and a constant refinement of the finishes and materials of the control plates.
The constant attention to market demands and a policy inspired by the constant improvement of the production processes and product quality has resulted in the addition of Tropea3, an innovative in-wall cistern, to the Valsir range of products.
Thanks to the rotating inlet fitting in brass.
Thanks to an innovative outlet valve that guarantees the correct consumption of water at each flush and adaptability to all types of WC pans.
Thanks to the use of materials that prevent the formation of limescale.
Activation can be mechanical, pneumatic or electronic, a demonstration of the extreme versatility of the product.
The reduced depth of the cistern allows it to be used in any type of installation.
Adjustment of the flush volume to 6/3 litres or 4.5/3 litres allows the reduction of water consumption following Green Building principles.
The stop valve is pre-fitted in all the Tropea3 cisterns to facilitate and accelerate installation; it is made up of an accessible closing device in brass and a molded body in PPSU, a technopolymer with an excellent mechanical performance.
The float valve was designed to ensure resistance to water hammer (10-30 bar) and to guarantee excellent levels of silence during the filling phase. The accessible internal filter ensures reliability and constant levels in performance.
A revolutionary outlet valve is behind the performance of the Tropea3 cisterns: reliability over time is guaranteed by the bottom seal made of a silicone blend and by the use of materials that delay the attack of limescale.
The tab is intended to keep the internal mechanisms in the correct position during handling until the cistern control plate has been completely installed.
The Valsir range of flush cisterns meets the aesthetic requirements of the market thanks to the design and the refined materials of the control plates.
The Valsir Design line of control plates is part of a project launched by Valsir destined for the showroom distribution channel and encompasses over 240 models produced using innovative and refined materials
the range of in-wall and external cisterns is accompanied by a complete series of pneumatic push buttons.
Tropea3 can be used in less common applications by using the optional components such as the remote pneumatic dual button for disability,
friendly bathrooms, the tamper-proof push button for installations in stadiums and prisons, or push buttons to facilitate the visually impaired.
Easy to use push buttons were designed for disability friendly bathrooms.
They were designed to make access to the buttons more practical thus ensuring water savings.
The tamper-proof push buttons make it easy to satisfy the installation requirements that are typical of public places, hotels, stadiums or prisons.
Designed for installation in walls of reduced thickness made of brick or wood with a floor standing WC pan.
Incorporates a galvanized sheet frame to be used with wall-hung pans in masonry rolls with reduced thickness.
Is equipped with a painted steel frame designed for installation in light walls (plasterboard, wood) with a wall-hung pan.
This is the most flexible frame of the entire range. Made of painted steel, it is designed for installations in plasterboard walls or mixed walls with a wallhung WC pan.
As of 1st September 2012 CE marking is required on all in-wall and external cisterns and is an important instrument for defining the level of quality and reliability of the product.
The CE marking contains the representative indicators of the performance of the product: durability, noise level and volume of water discharged are some of the fundamental parameters in product selection.
Tropea3 also meets the modern principles of Green Building, allowing significant water savings to be obtained and the reduction of flush volumes to 4.5 and 3 litres. In terms of performance, silence and durability Tropea3, thanks to the CE marking specifications achieved, is one of the best products in the world in its category
Tropea3 is available with the Ariapur odour extractor system which performs a dual extraction to ensure the perfect supply of fresh air to the bathroom.
The technology of Tropea3 installed in great buildings all over the world.
The range has been certified by the strictest certification bodes.
The stop valve is pre-fitted in all the Tropea3 cisterns to facilitate and accelerate installation; it is made up of an accessible closing device in brass and a molded body in PPSU, a technopolymer with an excellent mechanical performance.
The brass closing device is optimized to ensure the correct functioning over time.
Body made of polymer with mechanical properties comparable to those of brass.
Can be fully inspected even after installation thanks to the verifiable brass closing device.
The brass swivel fitting has been studied to greatly simplify the installation phase.
Fully pre-assembled and ready to install
The float valve was designed to ensure resistance to water hammer (10-30 bar) and to guarantee excellent levels of silence during the filling phase. The accessible internal filter ensures reliability and constant levels in performance.
Produced entirely with materials that prevent the formation of limescale.
Internal filter must be inspectionable to block the impurities present in the water that can damage the membranes of the float valve.
Every part can be completely disassembled and reassembled to allow cleaning.
Direct connection, without a flexible hose, between the stop valve and the float valve which reduces noise and allows fast maintenance.
Designed to provide resistance to extremely high pressures and water hammers.
A revolutionary outlet valve is behind the performance of the Tropea3 cisterns: reliability over time is guaranteed by the bottom seal made of a silicone blend and by the use of materials that delay the attack of limescale.
Unrivaled high pan cleaning performances thanks to the innovative outlet valve.
Made entirely with materials that prevent the formation of limescale and guarantee the reliability of the valve even in extreme conditions.
The rubber components are in compliance with EN681/WC, a guarantee of their unmatchable quality and resistance.
Discharges can be regulated from 6/3 to 4.5 liters/3 liters in order to minimize the water consumption and to respect the environment and the Green Building principles.
The tab is intended to keep the internal mechanisms in the correct position during handling until the cistern control plate has been completely installed.
Blocks all the inside components of the flushing cistern.
The device must be extracted in order to install the flushing cistern correctly, it does not allow the push plate to be placed until it is not removed.
Tropea3 was designed to allow installation inside any type of wall and for any type of WC pan.
Designed for installation in walls of reduced thickness made of brick or wood with a floor standing WC pan. The flush pipe allows an adjustment of 20 mm either up or down in order to correct any height misjudgements once the flooring has been completed.
All the materials necessary for installation are included in the packaging and it is available with the Valsir Ariapur odour extractor system.
Incorporates a galvanized sheet frame to be used with wall-hung pans in masonry rolls with reduced thickness. The anchor points of the pan and cistern are completely made of galvanized steel to guarantee maximum resistance to corrosion over time.
Tropea3 Fixsistem is available with the Valsir Ariapur odour extractor system.
Is equipped with a painted steel frame designed for installation in light walls (plasterboard, wood) with a wall-hung pan. The reduced thickness (90 mm) and the compact WC bend allow installation in any type of wall.
The painted surface makes the frame resistant to corrosion over time. Tropea3 Block S90 is available with the Valsir Ariapur odour extractor system.
This is the most flexible frame of the entire range. Made of painted steel, it is designed for installations in plasterboard walls or mixed walls with a wallhung WC pan. Thanks to the particular structure of the legs that are anchored to the floor, the frame does not require any other anchor points.
The painted surface makes the frame resistant to corrosion over time.
Valsir S.p.A.
Località Merlaro, 2
25078 Vestone (BS - Italy)
Tel. +39 0365 877 397
Fax +39 0365 81 268
valsir@valsir.it
